Diode–transistor logic (DTL) is a class of digital circuits that is the direct ancestor of

transistor–transistor logic Transistor–transistor logic (TTL) is a logic family built from bipolar junction transistors. Its name signifies that transistors perform both the logic function (the first "transistor") and the amplifying function (the second "transistor"), as o ...

. It is called so because the logic gating function (e.g.,

AND or AND may refer to: Logic, grammar, and computing * Conjunction (grammar), connecting two words, phrases, or clauses * Logical conjunction in mathematical logic, notated as "∧", "⋅", "&", or simple juxtaposition * Bitwise AND, a boolea ...

) is performed by a diode network and the amplifying function is performed by a

transistor upright=1.4, gate (G), body (B), source (S) and drain (D) terminals. The gate is separated from the body by an insulating layer (pink). A transistor is a semiconductor device used to Electronic amplifier, amplify or electronic switch, switch ...

(in contrast with RTL and

TTL TTL may refer to: Photography * Through-the-lens metering, a camera feature * Zenit TTL, an SLR film camera named for its TTL metering capability Technology * Time to live, a computer data lifespan-limiting mechanism * Transistor–transistor lo ...

Implementations

The DTL circuit shown in the picture consists of three stages: an input

diode logic Diode logic (DL), or diode-resistor logic (DRL), is the construction of Boolean logic gates from diodes. Diode logic was used extensively in the construction of early computers, where semiconductor diodes could replace bulky and costly active v ...

stage (D1, D2 and R1), an intermediate level shifting stage (R3 and R4), and an output common-emitter amplifier stage (Q1 and R2). If both inputs A and B are high (logic 1; near V+), then the diodes D1 and D2 are reverse biased. Resistors R1 and R3 will then supply enough current to turn on Q1 (drive Q1 into saturation) and also supply the current needed by R4. There will be a small positive voltage on the base of Q1 (V_BE, about 0.3 V for germanium and 0.6 V for silicon). The turned on transistor's collector current will then pull the output Q low (logic 0; V_CE(sat), usually less than 1 volt). If either or both inputs are low, then at least one of the input diodes conducts and pulls the voltage at the anodes to a value less than about 2 volts. R3 and R4 then act as a voltage divider that makes Q1's base voltage negative and consequently turns off Q1. Q1's collector current will be essentially zero, so R2 will pull the output voltage Q high (logic 1; near V+).

Discrete

The

IBM 1401 The IBM 1401 is a variable-wordlength decimal computer that was announced by IBM on October 5, 1959. The first member of the highly successful IBM 1400 series, it was aimed at replacing unit record equipment for processing data stored on pu ...

(announced in 1959) used DTL circuits similar to the circuit shown in the picture. IBM called the logic "complemented transistor diode logic" (CTDL). CTDL avoided the level shifting stage (R3 and R4) by alternating NPN and PNP based gates operating on different power supply voltages. NPN based circuits used +6V and -6V and the transistor switched at close to -6V, PNP based circuits used 0V and -12V and the transistor switched at close to 0V. Thus for example a NPN gate driven by a PNP gate would see the threshold voltage of -6V in the middle of the range of 0V to -12V. Similarly for the PNP gate switching at 0V driven by a range of 6V to -6V. The 1401 used germanium transistors and diodes in its basic gates. The 1401 also added an inductor in series with R2.IBM 1401 logic
Retrieved on 2009-06-28. The physical packaging used the

IBM Standard Modular System The Standard Modular System (SMS) is a system of standard transistorized circuit boards and mounting racks developed by IBM in the late 1950s, originally for the IBM 7030 Stretch. They were used throughout IBM's second-generation computers, per ...

Integrated

In an integrated circuit version of the DTL gate, R3 is replaced by two level-shifting diodes connected in series. Also the bottom of R4 is connected to ground to provide bias current for the diodes and a discharge path for the transistor base. The resulting integrated circuit runs off a single power supply voltage. In 1962,

Signetics Signetics Corporation was an American electronics manufacturer specifically established to make integrated circuits. Founded in 1961, they went on to develop a number of early microprocessors and support chips, as well as the widely used 555 time ...

introduced the SE100-series family, the first high-volume DTL chips. In 1964,

Fairchild Fairchild may refer to: Organizations * Fairchild Aerial Surveys, operated in cooperation with a subsidiary of Fairey Aviation Company * Fairchild Camera and Instrument * List of Sherman Fairchild companies, "Fairchild" companies * Fairchild Fa ...

released the 930-series DTμL micrologic family that had a better noise immunity, smaller die, and lower cost. It was the most commercially successful DTL family and copied by other IC manufacturers.

Speed improvement

The DTL

propagation delay Propagation delay is the time duration taken for a signal to reach its destination. It can relate to networking, electronics or physics. ''Hold time'' is the minimum interval required for the logic level to remain on the input after triggering ed ...

is relatively large. When the transistor goes into saturation from all inputs being high, charge is stored in the base region. When it comes out of saturation (one input goes low) this charge has to be removed and will dominate the propagation time. One way to speed up DTL is to add a small "speed-up" capacitor across R3. The capacitor helps to turn off the transistor by removing the stored base charge; the capacitor also helps to turn on the transistor by increasing the initial base drive. Another way to speed up DTL is to avoid saturating the switching transistor. That can be done with a

Baker clamp Baker clamp is a generic name for a class of electronic circuits that reduce the storage time of a switching bipolar junction transistor (BJT) by applying a nonlinear negative feedback through various kinds of diodes. The reason for slow turn-off t ...

. The Baker clamp is named for Richard H. Baker, who described it in his 1956 technical report "Maximum Efficiency Switching Circuits". In 1964,

James R. Biard James Robert Biard (May 20, 1931 – September 23, 2022) was an American electrical engineer and inventor who held 73 U.S. patents. Some of his more significant patents include the first infrared light-emitting diode (LED), the optical isolato ...

filed a patent for the

Schottky transistor A Schottky transistor is a combination of a transistor and a Schottky diode that prevents the transistor from saturating by diverting the excessive input current. It is also called a Schottky-clamped transistor. Mechanism Standard transistor ...

. In his patent the Schottky diode prevented the transistor from saturating by minimizing the forward bias on the collector–base transistor junction, thus reducing the minority carrier injection to a negligible amount. The diode could also be integrated on the same die, had a compact layout, no minority-carrier charge storage, and was faster than a conventional junction diode. His patent also showed how the Schottky transistor could be used in DTL circuits and improve the switching speed of other saturated logic designs, such as Schottky-TTL, at a low cost.

Interfacing considerations

A major advantage over the earlier

resistor–transistor logic Resistor–transistor logic (RTL) (sometimes also transistor–resistor logic (TRL)) is a class of digital circuits built using resistors as the input network and bipolar junction transistors (BJTs) as switching devices. RTL is the earliest class ...

is increased

fan-in Fan-in is the number of inputs a logic gate can handle. For instance the fan-in for the AND gate shown in the figure is 3. Physical logic gates with a large fan-in tend to be slower than those with a small fan-in. This is because the complexity o ...

. Additionally, to increase fan-out, an additional transistor and diode may be used.

References

External links

Diode-Transistor Logic (slides)
- University of Connecticut
Diode-Transistor Logic
- University of Babylon {{DEFAULTSORT:Diode-transistor logic Logic families